Tom‘s sleeve labeling machine has been fully affirmed by the majority of customers because of its excellent high-speed stable performance, unique dexterous design, and human-machine coordinated safety mode. The sleeve labeling machine has a wide range of applications and is suitable for many industries. The sleeve labeling machine is mainly used after the filling process. Although it is not the most important process in the whole process, it is also an indispensable key link in the entire production line. The adjustment of the sleeve labeling machine is an important step in the operation of the product.
Adjustment method of sleeve labeling machine
1.When the sleeve labeling machine starts to use, it is necessary to adjust the feeding mechanism of the plate, then put the sample in, and adjust the height of the material-arranging rod so that it can block the sample without rubbing the surface of the turntable.
2.In the docking conveying mechanism
First connect with the tray-arranging feeding mechanism and conveying. Put in the sample, adjust the guardrails at both ends, and then adjust the limit sheet metal spacing between the two sides of the outlet and the upper end, so that the sample can pass normally, but it can be stuck at the outlet. Then adjust the position of the electric eye, and the electric eye at the upper end of the outlet should be adjusted to the exit point , so that the butt conveying can be opened all the time, so that the samples can always be hooked out by the fixture one by one.
3.Labeling agency
First set the conveying speed (set in the servo drive in the electric box). Adjust the position of the radio eye so that the first fixture is aligned with the vacuum suction cup at the upper end. By adjusting the position of the fixture and the position of the vacuum suction cup cylinder. Within the error range, its fixture can be aligned with the vacuum plate.
4. Electric box mechanism of sleeve labeling machine
When placing the film, the film should be aligned with the central column, and the position of the electric eye next to it should be adjusted so that the film can be pulled normally. The central column should be clamped by the lifting mechanism and the sleeve labeling mechanism at the same time, so as to achieve three points and one line. Adjust the position of the electric eye for the distance of the cutter head, so that the sleeve labeling mechanism and the center column can just put the film on the fixture. The jig will not touch the above mechanism.
5. The outlet of the hair dryer should be inclined.
6. The position of the photographing mechanism should be adjusted so that the label film can be properly pressed in place.
7. The temperature of the electrothermal shrinking furnace mechanism should be adjusted so that the film can be shrunk without wrinkling, and the adjustment temperature depends on the material of the film.
Finally, running the debugging as a whole when you start it. The main thing is to adjust the continuity of the body operation, and the quality of the labeling of each set of fixtures. If the marks of some sets of fixtures are not aligned with the samples, first adjust the position of the fixtures, if not, adjust the fine-tuning fixtures.
Sleeve labeling machine operating procedures
1 Operational safety
Ensure that only trained and authorized personnel operate, schedule, and maintain equipment. Only professionals and equipment engineers are allowed to complete the layout and installation.
2.When operating the equipment, it is necessary to ensure
(1)Only after passing the professional training of the sleeve labeling machine manufacturer can it be operated.
(2) The operator must have the basic knowledge of the sleeve labeling machine in order to solve or adjust the equipment.
(3) Please operate according to the specified requirements when using the equipment.
3.Use environment, cannot be used in the following environments
(1) Sites with rapid temperature changes.
(2) Sites with high humidity and prone to dew.
(3) A site that causes the equipment to vibrate or shake a lot when working.
(4) Dusty venues.
(5) Sites where chemical substances are splashed.
(6) Places with flammable and dangerous goods.
(6) Places with flammable and dangerous goods.
4.Operating Instructions
(1) Before starting the equipment, check whether the bolts of each mechanism are loose.
(2) After the emergency stop switch is turned on, will the cutter mechanism automatically search for the origin.
(3) Before opening, make sure that the center guide column is installed in place to avoid damage to the center guide column and the cutter.
(4) After replacing the blade, please pay attention to whether the blade is too long, so as not to damage the tool.
(5) During standby or normal operation, do not put your hand into the working area of the cutter.
TOM ‘s sleeve labeling machine not only has a number of invention patents, but we will also take every machine we sell seriously, just like we treat our children. If you are still looking for a big brand, high-quality sleeve labeling machine, and production line supplier, you can feel free to get in touch with us.
